Share this content on Facebook!
08 Jul 2016

Tks industrial thermal oxidizers
Its important to are aware that your thermal oxidizers are constructed with quality so you ought to know the basic principles of the way thermal oxidizers work. Listed here is a brief outline of thermal oxidizers.


tks industrial company

The primary aim of the Thermal Oxidizer is to destroy the contaminants within the exhaust coming from a process. The process of the Thermal Oxidizer is based on the leading of combustion. The entire process of combustion is the most widely used strategy to control emissions of organic compounds.

Combustion based systems will always be simple systems competent at having high destruction efficiency. Methods typically consist of burners, which ignite the fuel and pollutants, and a chamber, which supplies the proper residence time for the combustion to happen. Combustion can be a chemical process due to the rapid mix of oxygen with assorted elements or substances producing discharge of heat. The whole process of combustion has been known as oxidation or incineration.

It's required to achieve complete combustion in the fuel gas so that no further air pollutants are added. To accomplish complete combustion after the contaminated air and fuel have been brought into contact, the subsequent conditions have to be provided: a temperature sufficient to ignite the waste-fuel mixture, turbulent mixing from the air and waste-fuel mixture, and sufficient residence here we are at the response to take place. These 3 the weather is referred to as the "three T's of combustion". The pace at which a combustible method is oxidized is greatly impacted by temperature. The greater the temperature, the faster the oxidation reaction will proceed.

The operation of ignition depends upon the next factors:

1. Energy combustibles within the waste stream.

2. Inlet temperature with the waste stream.

3. Rate of warmth loss from the combustion chamber.

4. Residence some time and flow pattern in the waste stream.

5. Combustion chamber geometry and materials of construction.


Thermal destruction on most organic compounds occurs between 590�F and 650�F. However, most hazardous waste incinerators are operated at 1400�F. The time for which the pollutants stay in the incinerator is termed residence time. The larger the residence time, the lower the temperature may be to the combustion chamber.

The residence duration of gases in the combustion chamber is calculated by

t = V / Q


t = residence time, seconds

V = chamber volume, ft3

Q = gas volumetric flow rate at combustion ft3/s.

Modifications to flow rates should be made for the excess combustion air added. For complete combustion that occurs, every particle of waste and fuel must are in contact with air (oxygen). If it doesn't occur, unreacted waste and fuel will probably be exhausted in the stack. Second, not the whole fuel or waste stream will be able to take direct connection with the burner flame.

Generally in most incinerators, part of the waste stream may bypass the flame and stay mixed at some point downstream with the burner together with the hot products of combustion. Several methods are used to improve mixing the environment and waste streams, such as the using refractory baffles, swirl-fired burners, and baffle plates. Unless properly designed, several mixing devices may create "dead spots" reducing operating temperatures.

The process of mixing flame and waste stream to get a uniform temperature for that decomposition of wastes is regarded as the difficult part within the form of an incinerator. A Thermal Oxidizer has to be designed thoroughly sufficient reason for proven techniques to achieve maximum mixing of airflows and also to avoid dead spots.


A Thermal Oxidizer includes a combustion chamber, a burner, as well as a blower to draw air with the complete oxidizer. With the contaminant-laden gas stream, air and fuel are continuously sent to the combustion chamber the place that the fuel is combusted.
The products of combustion as well as the unreacted feed stream enter in the reaction zone of the unit. The pollutants in the act air will be reacted at elevated temperature. The typical gas velocity ranges from 10 fps to 50 fps. Higher than normal velocities are helpful in preventing the particulates from settling down. The force liberated with the reaction could be directly recovered from process or indirectly recovered simply by using a heat exchanger.


The Thermal Oxidizer ought to be a number of material which may withstand high temperatures and the walls of the equipment are insulated to stop overheating in the outside walls of the unit. These units are generally furnished with sophisticated flame detection devices. The layer of insulation exposed in the Combustion Chamber is usually ceramic block which is 7" thick plus a density of 10 lbs./ft3.


There isn't any comment in this page yet!

Do you want to be the first commenter?

New Comment

Full Name:
E-Mail Address:
Your website (if exists):
Your Comment:
Security code: